Parts included correspond to the following original part #'s:  6N0711061A, 6N0711090A, 6N0711611C

This camshaft set consists of two camshafts for your VR6 that includes lube and specs.

Fits all VR6 2.8 2.9L Engines

- 272° duration
- Overlap 113° (Intake/Exhaust)
- Lift 11.2mm (Intake/Exhaust)
- Increase of 10-12 HP

Note: These are used camshafts that have been completely machined, refinished and hardened. A cost effect alternative for quick horsepower gains

Fits Vento/Jetta III, Golf III, Passat and Corrado.

Set includes front, right rear and left rear mounts. Replace them all at the same time and save yourself money!

Complete set of rings for one piston

Set includes 2 units as pictured

May be used to fasten the water pump

Corresponds to the original VW part number N90221803

Fits all VR6 engines equipped with a 70A alternator

Fits all VR6 engines equipped with a 90A alternator

Fits such alternators as on the VR6 engine.

This lightweight pulley only weighs 143g as opposed to the 370g of the original part. This reduction in weight helps reduce rotating mass which translates into increased performance especially at lower rpm.

Made of 6061 T6 Aluminum

NOTE: Please specify whether or not your car has air conditioning when ordering!

Will not fit 120A Alternators! Please order Item # AZVR004 in this case

Fits such alternators as on the VR6 engine.

This lightweight pulley only weighs 143g as opposed to the 370g of the original part. This reduction in weight helps reduce rotating mass which translates into increased performance especially at lower rpm.

Made of 6061 T6 Aluminum

Will ONLY fit 120A Alternators! Please order Item # AZ6811 if you DO NOT have a 120A alternator

- Includes an integrated harmonic balancer
- Weight savings of approx. 2.3 kg/5.06 lbs
- Provides better performance at lower rpm
- 6061 T6 Aluminum

All Pro Series Head Bolts are cold-forged to ensure molecular integrity, heat-treated prior to thread rolling and machining, and are rated nominally at 190,000 psi. ARP® Pro Series head bolt kits are application specific-designed for use with typically competition only components. These fasteners deliver superior strength and meet the ARP® "ZERO defect-ZERO failure" quality standard. Hardened and parallel-ground washers are included with each kit to ensure even load distribution and accurate torque readings. All Pro Series head bolts have a reduced wrenching 12-point head and wide area flange to eliminate the need for valve train removal for cylinder head retorquing and permits the use of larger diameter valve springs. Most applications have undercut short bolts that can help eliminate head gasket failures through providing more "stretch" to compensate for the additional compression of gaskets.

Set includes all fasteners required for the installation of one cylinder head.

Used to fasten the crank pulley/harmonic balancer on the crankshaft for the VR6

Corresponds to the original VW part numbers N0100873 and N0100875

Corresponds to the original VW part number N90544202 or N90544203

Polished Stainless Steel. Includes mounting hardware

Please specify your year, model and engine type when ordering

Please specify your year, model and engine type when ordering

For motors with plasic valve cover.

In order to replace all connecting rod bolts on a VR6 engine a total of 12 are required.

Corresponds to the original VW part number 021105425B

Fits Corrado VR6 - Coolant Reservoir->Throttle Valve Housing->Coolant Thermostat Housing->Radiator

Corresponds to original part # 535121101L

Also known as a "crackpipe". Fits all VR6 Engines

Fits all Corrado's equipped with the VR6 engine

Dimensions:
Length 285 mm
Width 240 mm
Height 95 mm
Weight 2.47 kg

Corresponds to the original part number 1H0253115C

Fits all VR6 engines

10 Recommended when replacing cluch & flywheel.

Corresponds to the original VW part number N90539801

10 Recommended when replacing cluch & flywheel.

Corresponds to the original VW part number N90539801

Fits all VR6 engines. Motor mount is a 2-piece unit

Fits all VR6 engines except those in Sharan and Transporter/Eurovan models with normal gearbox.

Corresponds to the original VW part number 1H0199273D