Fits Passat (excluding Syncro), Golf II and Corrado.

Set includes front, right rear and left rear mounts. Replace them all at the same time and save yourself money!

2.0L Throttle Body - 2E Engine found on Golf / Corrado / Vento equipped with automatic transmissions

Corresponds to the original VW part number 037133061AA

Fits a variety of different models and replaces the original part 357199381C

VF-Engineering designed, tooled up, and manufactured a complete new replacement containing a molded, high durometer polyurethane insert. The mount is constructed from billet aluminum and supplied with the highest tensile hardware available. Fitting should take no more than 30 minutes and is simplified if you support the gearbox and remove the bracket to the mount. This mount fits some MK2 Golf/Jettas and all MK3 Golf, Jetta, Passat, Vento VR6 and 8V GTIs, and Corrado VR6.

Note: May result in increased vibration/noise over stock mount

Includes piston rings and connecting rod bushing.

Includes piston rings and connecting rod bushing.

Parts included correspond to the following original part #'s:  6N0711061A, 6N0711090A, 6N0711611C

This adjustable cam sprocket enables precise adjustments to your cam timing. Tweak your engine to provide you with the power band right where you want it!

Update your Corrado with a chrome rear badge!

Fits the following transmissions (check the top of your transmission for applicable code)

AGC, ATB, ATA, AYK, AYN, AYL, CBA, CCM, CAW, AGK, CES, CGY, CHN and CGP

Corresponds to the original VW part number 02A398001

Fits all models/years

Fits G60 with 6 ribbed belt. Made of 6061 T6 Aluminum

Fits VW Corrado, Golf, Passat B3 and Jetta II

Corresponds to the original VW part number 037103493K

Fits all engine codes PG, 2E & ADY (Corrado G60 & 2.0L)

Corresponds to the original VW part number 049109111C

Flushes out and cleans the engine from the inside. Highly effective cleaning additive dissolves sludge and lacquer formers, coats solid particles and liquid contaminants. These are drained with the used oil during the oil change. After carrying out this type of prepared oil change, the fresh oil is able to realize its full performance potential: ˜ The engine develops its full performance again ˜ Runs with less wear ˜ Exhaust gas properties are optimised ˜ Deficient lubrication is minimized.

Operational area: Add to the engine oil BEFORE the oil change. After approx. 10 minutes idling, drain used oil, change the filter and fill with fresh oil. 500 ml is sufficient for engines holding up to 5 litres of oil.

Size: 65 mm x 25 mm

Corresponds to original part # 1J0853675ADPVQ

Corresponds to the original part number 1H0253115C

Hose is ordered in 1 meter lengths.

This GATES vacuum hose is extremely durable and perfect to replace existing aging lines especially since it features the same design as a fuel line. We recommend replacing all lines simultanously so as to avoid future and/or repeat failures in quick succession.

Used to fasten the crank pulley/harmonic balancer on the crankshaft for the VR6

Corresponds to the original VW part numbers N0100873 and N0100875

Corresponds to the original part number N90206103

For example may be used for flywheel attachment

Fits most VW models

Corresponds to the original VW part number N90288901

Compatible with virtually all VW and Audi engines

Please note that you will require the following number of bolts depending on your application:

- Corrado, Golf III, Passat, Vento, Sharan, T4 VR6 Motor  - 26 Bolts

- Corrado, Golf, Passat G60, 2.0l, 2.0l 16V - 20 Bolts

Corresponds to the original VW part number N90008401