4-piece set. Features thick high quality velour that is easy to clean

This camshaft set consists of one camshaft for your G60 engine and includes lube and specs.

Fits all G60 engines

- 272° duration
- 110° overlap (Intake/Exhaust)
- Lift 11.2 (Intake/Exhaust)
- Increase of 8-10 HP depending on overall condition of engine

Note: These are used camshafts that have been completely machined, refinished and hardened. A cost effect alternative for quick horsepower gains

This camshaft set consists of two camshafts for your VR6 that includes lube and specs.

Fits all VR6 2.8 2.9L Engines

- 272° duration
- Overlap 113° (Intake/Exhaust)
- Lift 11.2mm (Intake/Exhaust)
- Increase of 10-12 HP

Note: These are used camshafts that have been completely machined, refinished and hardened. A cost effect alternative for quick horsepower gains

Fits Passat (excluding Syncro), Golf II and Corrado.

Set includes front, right rear and left rear mounts. Replace them all at the same time and save yourself money!

Fits Vento/Jetta III, Golf III, Passat and Corrado.

Set includes front, right rear and left rear mounts. Replace them all at the same time and save yourself money!

Fits all years and models

Conversion Kit includes the following:

- 1 Wiper Arm - left side
- 1 Wiper Arm - right side
- 1 Wiper Blade - left side
- 1 Wiper Blade - right side
- 2 Wiper Caps

Contrary to popular belief, you do NOT require two driver's side blades.

These wipers provide you with a noticeable difference when clearing your windows of rain, snow, mist or anything else that might get sprayed on your windshield while driving. The aerodynamic design allows greater downforce onto the glass when travelling at higher speeds, contrary to most wiper systems. Additionally, the blade itself is spring loaded which creates equal downforce along the entire length thereby increasing the cleared surface area. This is an investment you will not regret!

Additional wiper blades are also available as spares or replacements

Includes 1 pair

Fits G60 etc.

Fits such alternators as on the VR6 engine.

This lightweight pulley only weighs 143g as opposed to the 370g of the original part. This reduction in weight helps reduce rotating mass which translates into increased performance especially at lower rpm.

Made of 6061 T6 Aluminum

NOTE: Please specify whether or not your car has air conditioning when ordering!

Will not fit 120A Alternators! Please order Item # AZVR004 in this case

- includes an integrated harmonic balancer
- Wights savings of approx. 2,3 kg
- Provides better performance at lower rpm

Fits all G60 engines

Wird geliefert wie abgebildet. Kleiner Riss auf linker Seite. (siehe Bilder unter Details)

Aluminum. Includes 2 pieces

Complete Cold Start Inclusion Kit to achieve D3 emissions levels for your Corrado G60 which will lower your road tax in Germany*. 

* Check local vehicles emissions requirement to see if this applies to your specific situation

Complete Cold Start Inclusion Kit to achieve D3 emissions levels for your Corrado G60 which will lower your road tax in Germany*. 

* Check local vehicles emissions requirement to see if this applies to your specific situation

Complete Cold Start Inclusion Kit to achieve D3 emissions levels for your Corrado G60 which will lower your road tax in Germany*. 

* Check local vehicles emissions requirement to see if this applies to your specific situation

Uses a 10mm socket

Uses a 10mm socket

Direct replacement for original part # 321201356A

Resembles the original part pictured - part #191145832D

Please note that the black hose pictured is the original part and the one being purchased is the blue one next to it.  

This conversion kit is required when installing the new Crystal Clear in.pro Turn Signals and Foglights on a Corrado G60 due to the fron bumper differences between this model and the VR6 model.

Detailed installation instructions are provided.

Made of metal and designed for Polo G40 engines. This gasket is slightly thinner than OEM and will raise your compression ratio and thus result in increased HP

Kits includes the following:

- Aluminum Waterpump Pulley
- Aluminum Power Steering Pulley

Kits includes the following:

- Aluminum Crank Pulley
- Aluminum Waterpump Pulley
- Aluminum Power Steering Pulley

Kits includes the following:

- Aluminum Crank Pulley (2.3kg/5.06 lbs reduction in weight)
- Aluminum Alternator Pulley (143g  vs. the original 370g)
- Aluminum Waterpump Pulley (187g vs. the original 410g)
- Aluminum Power Steering Pulley (224g vs. the original 454g)
- Made of 6061 T6 Aluminum

NOTE: Please specify whether or not your car has air conditioning when ordering!

Complete set of 6. Fits all 2.8 and 2.9L VR6 engines equipped with distributors and coilpacks. For engines equipped with distributors you may also order the matching ignition coil wire - part # AZS003

Complete set of 6. Fits all 2.8 and 2.9L VR6 engines equipped with distributors and coilpacks. For engines equipped with distributors you may also order the matching ignition coil wire - part # AZS011

This flywheel has been precisely machined and glass bead blasted. Flywheel is balanced within 0.02g!!! Core deposit required and will be refunded upon receipt of your original flywheel.

Fits all 2.8 and 2.9L VR6 engines

This flywheel has been precisely machined and glass bead blasted. Flywheel is balanced within 0.02g!!! Core deposit required and will be refunded upon receipt of your original flywheel.

Replaces original part # 021145255

Weighs approx. 224g vs. the original 454g which equals a weight reduction of 230g

Benefits:
- Less rotating mass which equals faster revving
- Increased fuel efficiency
- Imprved appearance over stock part

Replaces original part # 021121031A

Weighs approx. 187g  vs. the original of approx. 410g which works out to a weight reduction of 223g!

Benefits:
- Less rotating mass which equals faster revving
- Increased fuel efficiency
- Imprved appearance over stock part

Fits a multitude of vehicles such as Golf II, Corrado, Golf III, Vento and Jetta with a 4 X 100 bolt pattern

Drilled and slotted rotor helps vent gases and heat created by hard braking which can result in brake fade.

Dimensions: 226 X 10 mm (10.4')

Includes one pair

This adapter is required when installing the SAMCO hose kit

Adapter Kit includes the following:

- Steel Adapter Flange
- Gasket
- 2 Fastening Bolts

Adapter is delivered unpainted and unpolished

Update your Corrado with a chrome rear badge!

Fits all rear hatches. Regular steel with smooth edges.

Fits Golf II and Jetta II.

Corresponds to the original part number 191853852

100 mm in length (for additional measurements please refer to pictures)

Perfect for use with RS Outlet and Samco Hose Connector if these parts were purchased elsewhere.

Shaved rear hatch kit for Opel Astra G

Conversion Kit includes the following:

- Exact fitting steel license plate recess insert
- Solenoid
- Mounting plate for solenoid
- Bolts for above
- Linkage rods

Steel license plate recess is pre-drilled for easy mounting on the rear hatch. There is no drilling required on your existing hatch as existing factory holes are used for this installation.