This camshaft set consists of two camshafts for your VR6 that includes lube and specs.

Fits all VR6 2.8 2.9L Engines

- 272° duration
- Overlap 113° (Intake/Exhaust)
- Lift 11.2mm (Intake/Exhaust)
- Increase of 10-12 HP

Note: These are used camshafts that have been completely machined, refinished and hardened. A cost effect alternative for quick horsepower gains

Set includes 2 units as pictured

Fits such alternators as on the VR6 engine.

This lightweight pulley only weighs 143g as opposed to the 370g of the original part. This reduction in weight helps reduce rotating mass which translates into increased performance especially at lower rpm.

Made of 6061 T6 Aluminum

Will ONLY fit 120A Alternators! Please order Item # AZ6811 if you DO NOT have a 120A alternator

Fits such alternators as on the VR6 engine.

This lightweight pulley only weighs 143g as opposed to the 370g of the original part. This reduction in weight helps reduce rotating mass which translates into increased performance especially at lower rpm.

Made of 6061 T6 Aluminum

NOTE: Please specify whether or not your car has air conditioning when ordering!

Will not fit 120A Alternators! Please order Item # AZVR004 in this case

- Includes an integrated harmonic balancer
- Weight savings of approx. 2.3 kg/5.06 lbs
- Provides better performance at lower rpm
- 6061 T6 Aluminum

All Pro Series Head Bolts are cold-forged to ensure molecular integrity, heat-treated prior to thread rolling and machining, and are rated nominally at 190,000 psi. ARP® Pro Series head bolt kits are application specific-designed for use with typically competition only components. These fasteners deliver superior strength and meet the ARP® "ZERO defect-ZERO failure" quality standard. Hardened and parallel-ground washers are included with each kit to ensure even load distribution and accurate torque readings. All Pro Series head bolts have a reduced wrenching 12-point head and wide area flange to eliminate the need for valve train removal for cylinder head retorquing and permits the use of larger diameter valve springs. Most applications have undercut short bolts that can help eliminate head gasket failures through providing more "stretch" to compensate for the additional compression of gaskets.

Set includes all fasteners required for the installation of one cylinder head.

Polished Stainless Steel. Includes mounting hardware

Kits includes the following:

- Aluminum Waterpump Pulley (187g vs. the original 410g)
- Aluminum Power Steering Pulley (224g vs. the original 454g)
- Made of 6061 T6 Aluminum

Kit includes the following:

- Aluminum Crank Pulley (2.3kg/5.06 lbs reduction in weight)
- Aluminum Waterpump Pulley (187g vs. the original 410g)
- Aluminum Power Steering Pulley (224g vs. the original 454g)
- Made of 6061 T6 Aluminum

Kits includes the following:

- Aluminum Crank Pulley (2.3kg/5.06 lbs reduction in weight)
- Aluminum Alternator Pulley (143g  vs. the original 370g)
- Aluminum Waterpump Pulley (187g vs. the original 410g)
- Aluminum Power Steering Pulley (224g vs. the original 454g)
- Made of 6061 T6 Aluminum

NOTE: Please specify whether or not your car has air conditioning when ordering!

Will ONLY fit 120A Alternators! Please order Item # AZVR004 if you DO NOT have a 120A alternator

Kits includes the following:

- Aluminum Crank Pulley (2.3kg/5.06 lbs reduction in weight)
- Aluminum Alternator Pulley (143g  vs. the original 370g)
- Aluminum Waterpump Pulley (187g vs. the original 410g)
- Aluminum Power Steering Pulley (224g vs. the original 454g)
- Made of 6061 T6 Aluminum

NOTE: Please specify whether or not your car has air conditioning when ordering!

Will not fit 120A Alternators! Please order Item # AZVR004/2 in this case

Fits all 2.8 and 2.9L VR6 engines

This flywheel has been precisely machined and glass bead blasted. Flywheel is balanced within 0.02g!!! Core deposit required and will be refunded upon receipt of your original flywheel.

Replaces original part # 021145255

Weighs approx. 224g vs. the original 454g which equals a weight reduction of 230g

Benefits:
- Less rotating mass which equals faster revving
- Increased fuel efficiency
- Imprved appearance over stock part

Made of 6061 T6 Aluminum

Replaces original part # 021121031A

Weighs approx. 187g  vs. the original of approx. 410g which works out to a weight reduction of 223g!

Benefits:
- Less rotating mass which equals faster revving
- Increased fuel efficiency
- Imprved appearance over stock part
- Made of 6061 T6 Aluminum

This adapter is required when installing the SAMCO hose kit

Adapter Kit includes the following:

- Steel Adapter Flange
- Gasket
- 2 Fastening Bolts

Adapter is delivered unpainted and unpolished

SPECIFICATIONS
- Engine Code: AAA, ABV
- Diameter (mm): 2228
- Teeth: 28

Sintered metal plates

Fits: VW Corrado, Golf III, Passat and Vento/Jetta III

INFO
- Engine Codes: AAA, ABV
- Diameter (mm): 228
- Teeth: 28 

Will handle up to 420Nm/320 ft-lbs and includes Pressure Plate along with torsion sping clutch plate and specialized organic material

Includes all pictured parts . Please note that some models require the additional radiator flange bend (part # ARZ-SAM-VR-COR). The easiest way to determine whether or not you require this part is by standing in front of your radiator and confirming if the flange is at 90° or not. If it is NOT you will require the aforementioned part #.

Triple layered metal headgasket. This headgasket will increase your overall compression and as a result increase your performance. The use of new headbolts are required. Detailed installation specifications are included.

Perfect for use on all 2.8 or 2.9L VR6 engines.

Universal application. Includes mounting hardware.