Corresponds to the original partnumber 377853687CN

Self-adhesive

Dimensions: approx. 80 mm x 27 mm

Uses a 10mm socket

Uses a 10mm socket

• Sporty look
• Low maintenance and durable
• Easy replacement of antenna if required
• Antenna length approx. 410 mm
• Angled at 52°
• Impedence 150 Ω
• Installation hole size required 13 mm
• Installation depth required 35 mm
• Antenna cable length 350 mm
• +12V amplifier power supply is obtained from the car stereo 

Set includes:

- Fuse Holder
- Cover
- 2 Terminals

Drain Plug Washer A14 x 20

Corresponds to the original VW part number N0138492

Rechargeable LED Flashlight that recharges by plugging into your existing cigarette lighter outlet. A great piece of equipment to have on board in case of an emergency.

Corresponds to the original part number 7L6947175A

For enhanced security the antennamay only be extended using a special key (2 are included).

Dimensions: 56 mm x 26 mm

Corresponds to the original part number 1ML853687

Dimensions: 500 mm x 1000 mm X 0.9mm or 19.5" X 39" X 0.035"

Hose is ordered in 1 meter lengths.

This GATES vacuum hose is extremely durable and perfect to replace existing aging lines especially since it features the same design as a fuel line. We recommend replacing all lines simultanously so as to avoid future and/or repeat failures in quick succession.

Made from billet (solid) aluminum fitted with molded, high durometer polyurethane inserts. The body is constructed from billet aluminum. The VF-E drop link is a direct replacement and fitting should take no more than 30 minutes.

The mount is constructed from billet aluminum and supplied with high tensile hardware. Which means the stock mount will snap before the VF mount even bends. Fitting should take no more than 20 minutes maximum and fits all VAG Type 4 Chassis: Golf/Jetta 4, Beetle, Bora, Audi A3, and Audi TT.

Note: May result in increased vibration/noise over stock mount

VF-Engineering designed, tooled up, and manufactured a complete new replacement, containing specially designed molded high durometer polyurethane bushes. The mount is constructed from billet (ingot) aluminum and supplied with high tensile hardware. Billet is physically twice as strong as cast and this mount is designed for strength. VF recommends changing side mounts in pairs only. Fitting should take no more than 60 minutes usually.

Note: May result in increased vibration/noise over stock mount

VF-Engineering designed, tooled up and manufactured a complete new replacement, containing specially designed molded high durometer polyurethane bushes. The mount is constructed from billet (ingot) aluminum and supplied with high tensile hardware. Billet is physically twice as strong as cast and this mount is designed for strength. VF recommends changing side mounts in pairs only. Fitting should take no more than 60 minutes usually.

Note: May result in increased vibration/noise over stock mount

VF-Engineering designed, tooled up and manufactured a complete new replacement, containing specially desinged molded high durometer polyurethane bushes. The mount is constructed from billet (ingot) aluminum and supplied with high tensile hardware. Billet is physically twice as strong as cast and this mount is designed for strength. Fitting should take no more than 60 minutes and fits all MK4 chassis including Golf, Jetta, Bora, Beetle, Audi TT, A3, and S3. VF recommends changing side mounts in pairs only.

Note: May result in increased vibration/noise over stock mount

To reduce this movement VF-Engineering made a complete replacement billet mount fitted with molded, high durometer polyurethane inserts. The mount is constructed from billet aluminum and supplied with high tensile hardware. Which means the stock mount will snap before the VF mount even bends. Fitting should take no more than 20 minutes maximum.

Note: May result in increased vibration/noise over stock mount

VF-Engineering designed, tooled up and manufactured a complete new replacement, containing specially designed molded high durometer polyurethane bushes. The mount is constructed from billet (ingot) aluminum and supplied with high tensile hardware. Billet is physically twice as strong as cast and this mount is designed for strength. Fitting should take no more than 60 minutes and fits all MK4 chassis including Golf, Jetta, Bora, Beetle, Audi TT, A3, and S3. VF recommends changing side mounts in pairs only.

Note: May result in increased vibration/noise over stock mount

Note: May result in increased vibration/noise over stock mount

Highly flexible and temperature resistant harness replaces your defective harness where it is most likely to break. Connectors are included and using this will save you substantial money as opposed to replacing the entire wiring harness.

Easy Installation:
Any experienced technician will be able to install these with ease.